Up-Map T800+ App Based ECU Reflash
For Tuono 660
See Complete fitment list at bottom of this page.
This is a Bluetooth Andriod or iOS smartphone app based Plug-and-Play option to get RACE (aka full power/full system exhaust compatible) mapping on your 660.
When you buy this product, you get the Up-Map T800+ module, the canbus cable, and download the respective app on your Android or iOS smartphone.
This is a full power RACE only ECU flash for the RS660. All rider aid functions are retained, all dashboard functionality is retained, and the Pit Lane Speed Limiter is enabled. The T800+ module is supplied with two maps: the base RACE map and a stock map (so owners can revert at any time to stock map, if they choose).
Most importantly, this is a safe and correct way to run an aftermarket exhaust with no catalytic converter or removing any servo's or EGR system components.
ABS can be turned off for the rear wheel only. Front wheel ABS is always active.
The Upmap comes with three maps:
- Stock map for bike restore to OEM status plus two alternative maps are supplied free with the tool. More maps can be brought from the map store if needed.
- The second map is a factory map for your model, you can choose the OEM Race map (this is what AF1 Racing recommends), or an alternative non-race map for your model, if applicable Use the promo code FREERACE to download it for free!
- Third map is a Gabro Racing tuned map: surf the map store via the App and choose the tuned map applicable to your bike mods so read map description very well. Use the promo code GRTMAP to download it for free!
Again, the codes to access the maps are FREERACE and GRTMAP. These codes are valid only for UpMaps sold by AF1 Racing.
Peak power gains with this ecu flash are nominal; our test bikes showed between 1 and 4 horsepower peak, when used with an Akrapovic or SC Project exhaust. Biggest gains are in mid range rpms where power improvements were consistently 4-6 hp.
Additional indepth discussion of this product can be seen at this link on www.apriliaforum.com
The official installation and use manual in .pdf format and the full app user manual in .pdf format.
Please note: This ECU flash disables the front fairing mounted front turn signals. Instead, when the turn signal button is pressed, the RH or LH LED eyebrows in the stock headlight illuminate, depending on which way you push the turn signal switch (RH activates RH brow LED, LH activates LH brow LED). Most owners elect to remove the stock turn signals after a RACE flash and replace them with the AF1 Racing Turn Signal Cover Kit
Some additional use and activation notes are below:
Once logged in the app and connected/paired the tool and app to the bike, you can download the stock map for restore.
Then go to the map store and download the race map using the coupon code "free-race"
Each T800+ marries only one ECU/Bike, so it can be used on your bike only.
Initial slow speed file transfer due to bluetooth instability has been solved. UpMap can be used on both Android and IOS phone/tablets.
The flashing process lasts about 15min, this new Marelli 11MP ECU stores a very big map file and needs time to download and write it down.
It is strongly recommended to use a battery tenders on the bike battery and to keep your smartphone plugged into it's charger during the flashing process.
By the end of the flash the T800+ automatically performs throttle learning and errors reset. It will ask you to key-off/key-on the bike.
Once the ECU has been flashed you can choose if remove the Upmap T800+ module from the bike or leave it connected. It goes standby after 30 minutes of bluetooth inactivity. Battery drain from the UpMap during standby is negligible.
OBD errors log/erase has been recently added to the App, so you'll be able to check error codes and reset them, if needed.
FOR CLOSED COURSE COMPETITION USE ONLY. NOT INTENDED FOR STREET USE. LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR USE, UPON A HIGHWAY.